Men så då hände det otroliga, jag hittade en guide som funkade klockrent!!
Till och med slapp xlg inloggning och kan nu logga in som vanligt med Gnome session.
Jag länkar + skriver den här inne, så att guiden alltid finns för alla.
I have put this tutorial together from these two articles:
* https://help.ubuntu.com/community/RadeonDriver
* http://wiki.beryl-project.org/wiki/Inst ... with_AIGLX
Detta är testat med ett Radeon 9600 AGP 256 MB, funkar perfekt efter denna guide.
Please make sure that you have all updates installed on your Ubuntu Feisty Fawn desktop before you try this.
2 Find Out About Your Graphic Card
First you should find out about your graphic card. Open a terminal (Applications > Accessories > Terminal) and type
Kod: Markera allt
lspci
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 [Mobility FireGL 9000] (rev 01)
(This output is from my notebook which uses an ATI Mobility Radeon 9200 graphic card.)
The following list shows which ATI graphic cards can use Beryl (your graphic card should be listed under Full 3D Support if you want to use Beryl):
Full 3D Support
* 7000 / rv100 based cards.
* 7200 / R100 based cards.
* 7500 / rv200 based cards.
* 8X00 / R200 based cards.
* 9000 / rv250 based cards.
* 9100 / R200 based cards.
* 9200 / rv280 based cards.
Experimental 3D Acceleration
* 9500 / R300 based cards.
* 9600 / rv350 or rv360 based cards.
* 9700 / R300 based cards.
* 9800 / R350 or R360 based cards.
* X300 / rv370 based cards.
* X600 / rv380 based cards.
* X700 / rv410 based cards.
* X800 / R420 or R423 or R430 or R480 based cards.
* X850 / R480 or R481 based cards.
2D Acceleration Only
* Xpress 200M Northbridge integrated GPUs
Unsupported
* X1300 / R515 based cards.
* X1600 / R530 based cards.
* X1800 / R520 based cards.
* X1900 / R580 based cards.
3 Configure AIGLX Plus The Open-Source ATI Driver
We want to use AIGLX with open-source ATI driver instead of XGL with the proprietary ATI driver (fglrx). Therefore we have to disable fglrx. First we disable the fglrx kernel module:
Kod: Markera allt
sudo modprobe -r fglrx
Kod: Markera allt
glxinfo | grep vendor
server glx vendor string: SGI
client glx vendor string: SGI
OpenGL vendor string: Tungsten Graphics, Inc.
If you have ATI in the output of the previous command, remove the fglrx driver like this (you can do this also if you have SGI in the output - just to go sure):
Kod: Markera allt
sudo apt-get remove xorg-driver-fglrx; sudo apt-get install libgl1-mesa-glx libgl1-mesa-dri
Kod: Markera allt
sudo gedit /etc/X11/xorg.conf
Kod: Markera allt
Section "Device"
Identifier "ATI Technologies Inc Radeon R250 [Mobility FireGL 9000]"
Driver "ati"
BusID "PCI:1:0:0"
EndSection
Kod: Markera allt
Section "Device"
Identifier "ATI Technologies Inc Radeon R250 [Mobility FireGL 9000]"
Driver "radeon"
BusID "PCI:1:0:0"
Option "XAANoOffscreenPixmaps"
Option "AGPMode" "4"
Option "AGPFastWrite" "true"
Option "DisableGLXRootClipping" "true"
Option "AddARGBGLXVisuals" "true"
Option "AllowGLXWithComposite" "true"
Option "EnablePageFlip" "true"
EndSection
The Monitor and Screen sections in /etc/X11/xorg.conf should be alright.
Also replace
Kod: Markera allt
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
InputDevice "Synaptics Touchpad"
EndSection
Kod: Markera allt
Section "ServerLayout"
Option "AIGLX" "true"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "Generic Keyboard"
InputDevice "Configured Mouse"
InputDevice "stylus" "SendCoreEvents"
InputDevice "cursor" "SendCoreEvents"
InputDevice "eraser" "SendCoreEvents"
InputDevice "Synaptics Touchpad"
EndSection
And finally add the following two sections to the end of /etc/X11/xorg.conf if they don't exist elsewhere in the file:
Kod: Markera allt
Section "DRI"
Mode 0666
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
Afterwards, run
Kod: Markera allt
glxinfo | grep vendor
server glx vendor string: SGI
client glx vendor string: SGI
OpenGL vendor string: Tungsten Graphics, Inc.
Then run
Kod: Markera allt
glxinfo | grep "direct rendering"
direct rendering: Yes
Nu borde grafikkortet vara installerat och klar.
Sen kommer resten av guiden för Beryl...
http://www.howtoforge.com/ubuntu_feisty_beryl_ati_radeon_p2?s=0b7fc5ecfeb05fbc6a8c266c15cdd9a2&
http://www.howtoforge.com/ubuntu_feisty_beryl_ati_radeon_p3?s=0b7fc5ecfeb05fbc6a8c266c15cdd9a2&
orginal guiden finns här:
http://www.howtoforge.com/ubuntu_feisty_beryl_ati_radeon
Unofficial Wiki for the ATI Linux Driver
http://wiki.cchtml.com/index.php/Main_Page
Unofficial Wiki for the ATI Linux Driver Ubuntu
http://wiki.cchtml.com/index.php/Ubuntu
Drivrutiner för ATI kort:
http://ati.amd.com/support/driver.html
Envy script: Envy Script(ATI/Nvidia):
http://www.albertomilone.com/nvidia_scripts1.html